High Availability (HA) in PaloAlto Firewall with reference command


##################### HA ####################################

>show high-availability state                            ##HA state/configuration/ Synchronization state

>show high-availability state-synchronization            ##Synchronization status/

>show high-availability control-link statistics          ##control-link statistics 

>show high-availability transitions                      ##Transition Statistics counters 

>show high-availability interface ha1                    ##HA interface state/counters/rx/tx/drop

>show high-availability ha2_keepalive                    ##HA2 Keep-Alive statistics

>show high-availability flap-statistics                  ##flap statistics

>show high-availability all                              ##HA status 

>request high-availability state suspend                 ##put firewall in suspended state 

>request high-availability state functional              ##put firewall in functional state 

>​​request high-availability sync-to-remote running-config       ##sync running config to peer 

>show high-availability virtual-address                                   ##active/active virtual address 

>show log system subtype equal ha                                      ##ha logs 

#######################################LOGS################################

1) Dashboard>Monitor>system 

2) show log system/show log system subtype equal ha

3) less mp-log _agent.log

4) show session id xx | match HA

5) show counter global filter aspect aa delta yes 

6) debug high-availability on debug 

7) debug high-availability internal-dump

8) debug high-availability dataplane-status

9) debug high-availability flap-interface ha1/2/3/4       ##flap a ha interface 


############################################################################

Comments

Post a Comment

Popular posts from this blog

Configure IPsec site-to-site VPN in Linux Machine

Image
 Configure IPsec site-to-site VPN in Linux Machine: Update the system and install the package  apt update && sudo apt upgrade -y  apt install strongswan -y Check if the following kernel parameter is set or not sysctl net.ipv4.ip_forward=1 To list all configured parameters: sysctl -a root@ubuntu-server-main:~# sysctl net.ipv4.ip_forward=1 net.ipv4.ip_forward = 1 root@ubuntu-server-main:~# sysctl net.ipv4.conf.all.accept_redirects=0 net.ipv4.conf.all.accept_redirects = 0 root@ubuntu-server-main:~# sysctl net.ipv4.conf.all.send_redirects=0 net.ipv4.conf.all.send_redirects = 0 root@ubuntu-server-main:~# Network Diagram: IPsec Config: Configure the PSK and update the VPN endpoints ++++++++++++++ cat /etc/ipsec.secrets # source      destination 192.168.0.2   192.168.0.108 : PSK "87zRQqylaoeF5I8o4lRhwvmUzf+pYdDpsCOlesIeFA/2xrtxKXJTbCPZgqplnXgPX5uprL+aRgxD8ua7MmdWaQ" ++++++++++++++ cat /etc/ipsec.conf: config setup         ch...
Read more

TACACS+ Installation on Linux [CentOS]

 TACACS+  Installation on CentOS: In the example below I will show you how to install tac_plus on a CentOS server. There’s a RPM available so this will save you the hassle of compiling the source code yourself. Let’s add the repository first: [root@server ~]# cd /etc/yum.repos.d/ [root@server yum.repos.d]# vim nux-misc.repo We will create a new repository file where we can grab tac_plus. This is what you should enter: [nux-misc] name=Nux Misc baseurl=http://li.nux.ro/download/nux/misc/el6/x86_64/ enabled=0 gpgcheck=1 gpgkey=http://li.nux.ro/download/nux/RPM-GPG-KEY-nux.ro Save the file and install tac_plus with the following command: [root@server ~]# yum --enablerepo=nux-misc install tac_plus That’s all you need to do. All configuration is done from a single config file. Let’s take a look at its contents: [root@server /]# vim /etc/tac_plus.conf You will see a lot of things in this default configuration file. Let me walk you through some of the fields. The first thing you see ...
Read more

Free Radius setup/configuration in Linux [Ubuntu/CentOS]

Free Radius setup/configuration in Linux [Ubuntu/CentOS]   1) Free RADIUS Client: CentOS:  yum install freeradius-utils Ubuntu: apt-get install freeradius-utils   2) Free RADIUS Server: Add the client device to free RADIUS server: i) vi /etc/freeradius/3.0/clients.conf  ii) Append below lines to the file above ############# client FortiGate-VM64-Xen {        ipaddr           = 192.168.0.108        secret           = testing123 } client sumit-linux-amp {        ipaddr           = 192.168.0.190        secret           = testing123 } #############   iii) Add users to the RADIUS server: Append below lines to the file "users" > vi /etc/freeradiu...
Read more